配件係列
草莓视频下载链接縫紉機,品質鑄就未來走進草莓视频下载链接
一般故障的處理方法/The treatment methods of general malfunction:
故障類型 Kinds of malfunction |
故障情況 Appearances of malfunction |
發生故障的原因 Causes ofmalfunction |
處理方法 The treatment methods |
斷針 Needle broken |
縫物過厚時斷針 Needle breaks when sewing thick materials |
針尖刺偏或彎曲造成與鉤針相碰 Collide with the hook hecause of the needlepoint prick inclined or be bended |
Stop using and replace broken needle <- 點擊查看視頻 |
機針與壓腳或鉤針相碰 Themeedle collides with the presser foor or the hook |
壓緊導架或壓腳及鉤針鎖緊螺絲鬆動 The press guide holder or the presser foot or the hook screw is loose |
檢查後擰緊 Check it then tighten up the screw |
|
跳針 Shortage Of stitches |
機針沒有穿入鉤針線圈 The needle does’t prick to the thread loop of the hook |
機針偏高,下行時機針動作相對滯後 The action of the needle falling lags relatively because the needle position is too high |
對照說明書調整 Contrast the Instructions to adjust
|
鉤針不勾線 The hook deesn’t catch the thread |
鉤針與機針缺口平麵間隙過大 The gap is too big between the plane of the needle and the hook |
對照說明書調整 Contrast the Instructions to adjust
|
|
或機針偏高,鉤針動作相對滯後 The action of hook lags relatively because the needle position is too high |
|||
快速縫厚物時偶爾跳針 Occasionally occur the shortage of stitches when sew the thicker materials quickly
|
機針缺口平麵傾斜 The plane of the needle gap is inclined |
||
縫線張力不均,時緊時鬆造成 The sewing tension is unequally so that the thread is tight and loose intermittently |
Replace the high-quality thread <- 點擊查看視頻 |
||
斷線 Thread broken |
線頭呈剝絲狀 The thread end is peeled filiform |
機針的針孔或線槽不光滑 The needle eye/slot is rough |
Replace the new needle <- 點擊查看視頻 |
尾線很毛 The thread end is very rough |
針板孔及鉤針頭表麵粗糙 The needle plate hole and the surface of the hook top is rough |
用砂布打磨 Use gauze to polish |
|
線頭呈割斷狀 The broken thread end looks like being cutted |
機針孔粗糙,壓線器太緊 The needle eye is rough and the presser foot is too tight |
檢查後更新調整 Use gauze to polish |
|
麵板的挑戰器太高等造成 The picking thread implement is too high |
|||
其他 Others |
送料不流暢 Feeding the materials doesn’s smooth |
壓腳表麵不光滑,送料牙齒尖不鋒利,送料牙抬升高度不夠 The surface of presser foot is rough, the giving materials teeth aren’t sharp and the height of the giving materials teeth aren’t high enough |
更換壓腳,更換牙齒,抬高牙齒高度 Replace the presser foot and the giving materials teeth, and raise the height of the teeth |
出尾時不流暢 Out of the end doesn’t smooth |
送料牙與壓腳底麵接觸不平 The contace sur face between the giving materials teeth and the presser foot is rough |
修整壓腳底麵 Adiust the surface of the presser foot |
|
電機 The electric motor |
電機不轉 The electric motor does not rotate |
檢查碳刷是否磨損 Check if t he carbon brush wears away |
更換新碳刷 Replace the new carbon brush |
電機不轉或轉過高 The electric motor does not rotate or rotates too quick |
開關接觸不良以及整流管燒壞 Switch contacts badly and rectifier tube is burned out |
更換新開關以及新整流管 Replace the new switch and the new rectifier tube |
零件名稱及編號對照示意圖/The sketch maps of parts name &serial NO:
件 號 Parts No. |
零件名稱 Denomination |
件 號 Parts No. |
零件名稱 Denomination |
件 號 Parts No. |
零件名稱 Denomination |
A001 |
線丁帽 Wire nail cap |
A027 |
針杆 Needle pole |
A053 |
刀架彈簧 Tool post spring |
A002 |
線丁 Wire nail |
A028 |
針杆連接 Needle pole joint |
A054 |
平行軸 Parallel axis |
A003 |
托線盤 Enrouleur |
A029 |
壓杆下套 Pressur rod underside sleeve |
A055 |
刀架 Tool post |
A004 |
手輪護架 Handwheel cage |
A030 |
壓腳底 Presser foot bottom |
A056 |
定刀片 Fixed blade |
A005 |
主軸壓墊 Mail axis cushion |
A031 |
壓杆導架 The guide holder of pressure rod |
A057 |
滑塊 Slippper |
A006 |
滾動軸承1026 Rolling bearing |
A032 |
壓緊杆 Pressure rod |
A058 |
鉤針軸下軸套 Hook axis sleeve |
A007 |
大連杆 Big connecting |
A033 |
壓杆彈簧 Pressure rod spring |
A059 |
牙架軸承800 Feedbase bearing 800 |
A008 |
杆端關節軸承 Rod end jiont bearing |
A034 |
壓杆上套 Pressure rod upside sleeve |
A060 |
凸輪 Cam |
A009 |
盤形槽皮帶輪 Disk slot belt sheave |
A035 |
壓腳彈簧螺丁 Pressure rod spring screw |
A061 |
凸輪墊片 Cam washer |
A010 |
曲柄滾球 Crank roller |
A036 |
麵板 plate |
A062 |
開關 Switch |
A011 |
鉤針曲柄 Hook crank |
A037 |
過條線 The threading srtip |
A063 |
開關按鈕 Switch button |
A012 |
開口卡簧Ф8 CirclipФ8 |
A038 |
罩殼套 Enclosed plate |
A064 |
開關護罩 Switch shield |
A013 |
鉤針軸上軸套 Crochet hook axial sleeve |
A039 |
送料牙 Giving material teeth |
A065 |
手輪 Handwheel |
A014 |
杠杆軸 Carrying pole axis |
A040 |
牙架 Feed base |
A066 |
主箱蓋 Main case cover |
A015 |
杠杆 Carrying pole |
A041 |
主軸 Mail axis |
A067 |
標牌蓋 Label cover |
A016 |
開口卡簧Ф3 CirclipФ3 |
A042 |
鉤針架 Latch needle frame |
A068 |
轉子 Rotor |
A017 |
鏈條節 Chain joint |
A043 |
鉤針 Hook |
A069 |
碳刷 Carbon brush |
A018 |
鏈條節銷 Chain joint pin |
A044 |
壓腳板手螺丁 Presser foot wrench screw |
A070 |
碳刷蓋 Carbon brush cover |
A019 |
電機 Motor |
A045 |
壓腳板手螺丁 Presser foot wrench |
A071 |
電源線 Power cord |
A020 |
皮帶輪 Belt sheave |
A046 |
壓杆導板 Presser rod guide plate |
A072 |
針夾 Clip |
A021 |
同步帶 Ynchronous belt |
A047 |
針板螺丁 Neddle plate screw |
A073 |
刀架軸套 Tool holder shaft sleeve |
A022 |
皮帶輪夾圈 Belt sheave clamp ring |
A048 |
針板 Needle plate |
A074 |
230#機針 230#needle |
A023 |
過線環 The threading loop |
A049 |
鉤針架軸 Hook gude axis |
A075 |
扭簧螺丁M5x30 Broom screw M59*30 |
A024 |
機殼 Machine case |
A050 |
主軸軸承600 Bearing 600 |
A076 |
扭簧 Broom spring |
A025 |
壓線器 Pressing thread implement |
A051 |
動刀片 Driving blade |
A077 |
壓線器過線 Presser thread guide |
A026 |
針杆套 Neddle pose sleeve |
A052 |
刀架軸 Tool post axis |
A078 |
Ф2.5肖丁 Ф2.5dowel |
0577-85303282
地址:溫州市104國道仙岩路口竹溪工業園
銷售熱線:0577-85303282
傳真:0577-85313282
聯係人:潘經理
手機:15355877706
郵箱:admin@sh-survey.com
微信公眾號
手機站